The "new generation" DJ-V17 is loaded with features, including: New, two-touch repeater access High grade waterproof materials compatible to IPX7* (submersible 1m/3ft. for 30 min.) Rugged polycarbonate body resists dirt, dust and moisture Highly visible backlit alphanumeric display Direct frequency input through illuminated keypad 200 Memories and one call channel VFO, Memory and Scan modes Ultra-flexible antenna with SMA connector avoids breakage 39 CTCSS tone squelch (encode+decode) settings Tone burst function (1,000, 1450, 1750 and 2100Hz) Battery-drain function avoids memory-effect Ergonomic design, fits in the palm of your hand Wire cloning capability Ni-MH standard and varieties of optional batteries including Li-ION packs 2-level attenuator Waterproof single mic/speaker jack DTMF Autodialer with Memory includes nine autodial memories plus redial function * The IEC 60529/IPX7 is an European system of test specification standards for classifying the degrees of protection provided by the enclosures of electrical equipment. An IPX7 designation means that the unit withstands immersion in one meter (approx 3ft) of still water for up to 30 minutes.The factory guarantees this grade for 1 year provided all the jack covers are properly and securely closed. However, Please understand that DJ-V17 is not an IPX8 (water-resistant) grade, NOT even IPX7 COMPLIANT (but compatible); water-pressure such as washing the unit with running water may cause damage to the unit and voids warranty. Never immerse the unit uselessly under the water. V/UHF signal does not propagate in water.If the unit is dropped in water, please pick it up immediately and wipe with a clean dry cloth.

SPECIFICATIONS
General
Frequency range:	T: TX144 - 147.995MHz RX130 - 173.995MHz E: TX/RX 144 - 145.995MHz
Modulation:	F3E (FM)
Frequency step:	5,10, 12.5, 15, 20, 25, 30kHz step
Memory channel:	200 channels + 1 call channel + 1 Repeater-Access parameter memory
Antenna impedance:	50ohm unbalanced
Frequency stability:	+/- 5ppm
Supply voltage:	DC 7.0 - 16.0V (EXT DC-IN)
Current consumption:	1.4A (typical) Transmit high at 5W / 250mA (typical) Receive at 500mW / 70mA (typical) Standby / 25mA (typical) Batt.save on
Temperature range:	Unit -10digC to 60digC (+14digF to +140digF) Battery packs: -10digC to +45digC (+14digF to +113digF)
Ground:	Negative
Dimensions:	58(W)x110(H)x36.4(D)mm (2.28"(W)x4.33"(H)x1.43"(D)) with EBP-65N w/o projection
Weight:	Approx.280g (9.9oz) with EBP-65N & antenna
Transmitter
Power output:	Approx. 5W (with EBP-65N) Approx. 5W (with DC 13.8V) Approx. 0.8W (LOW output)
Modulation:	Variable reactance
Spurious emission:	-60dB or less
Max. deviation:	+/- 5KHz
Mic. impedance:	2Kohm
Receiver
System:	Double-conversion super heterodyne
Sensitivity:	-14.0dBu (0.2uV) or less
Intermediate frequency:	1st IF 21.7MHz 2nd IF 450kHz
Selectivity:	-6dB: 12kHz or more -60dB: 26kHz or less
AF output:	500mW (MAX) / 400mW (8ohm, 10% distortion)
Specifications subject to change without notice or obligation. Specifications apply to Amateur Radio bands only. Permits required for MARS use. Product intended for use by properly licensed operators.

STANDARD ACCESSORIES

Ni-MH battery pack EBP-65 (7.2V 700mA) EDC-146(T) or EDC-147(other versions) wall-charger Flexible whip antenna (EA0141 or EA0142 depending on the versions) Belt clip Hand strap Instruction manual Accessories may differ depending on the versions. Please contact your dealer for standard accessories and warranty-policy.